Call for Immediate Service(503) 300-4519

How To Avoid Frozen Pipes This Winter

Protecting Pipes This Coming Winter

Protecting vulnerable plumbing pipes from freezing winter weather can dramatically reduce the risk of water pipes breaking and flooding your home. Frozen pipes create high pressure within the pipe and prevent water from flowing. Good plumbing services can detect signs of pipe freeze. An early sign of pipe freeze is when there is no water flowing when a tap is turned on. If your pipe breaks, you must repair it as soon as possible to prevent further damage to your property.

If your pipe cannot thaw and it bursts, you need professional help. If you need help with plumbing work with frozen pipes or other problems this winter, call a professional immediately as pipe bursts are seldom within the realm of self-repair.

Anyone who has had problems with frozen pipes in the past can cite that full blockages aren’t always the case. Sometimes, the water is partially blocked resulting in dips. Dripping fountains are one of the easiest ways to prevent the pipes from freezing, as even a small amount of water flowing through the pipes can help thaw out the block. If you let the gutter run through a pipe, it can also help thaw the pipe and melt the ice so that the pipe does not freeze. By allowing even a small trickle by even an inch or two, the drain can get unblocked – from water flowing in the water pipes.

If you have a frozen pipe that has not burst, take the following steps to defrost it and prevent it from bursting. If you do not believe that the pipe can be defrosted safely, or if you do not know where it is located and cannot get to the frozen length, always remember to call a professional.

Foresight In Pipe-Laying

If you have experienced a frozen pipe in your home this past winter, work with a specialist to lay the pipe for future frost prevention. First of all, people should learn more about what happens to pipes when they freeze and how to deal with frozen or burst pipes at home. If you take precautions to prevent your pipes from freezing, pay particular attention in these areas for next winter.

Pipe Insulation

Get ahead of the icy weather by insulating your pipes properly and preparing them for the winter season. Learn more about what you can do to reduce the risk of freezing pipes and help with maintenance and DIY tasks to protect your sanitation system and prevent pipes from freezing in the winter months.

To avoid frozen pipes and ruptures, which can cost thousands of dollars to repair, consider what signs and precautions you should take.

Mistakes In Pipe Laying

  • Mistake 1: Mismatching Threaded Fittings
    You go to install a new gas range or gas dryer and mismatch iron pipe threads and flare compression threads.
    Inevitably, this leads to a leaky gas connection, a fire hazard. The safest thing you can do is buy a gas connector kit that already has the specialty fittings you need to make a gastight transfer from the wall to the appliance. Freezing can occur in pipes where the material is leaking.
  • Mistake 2: Skipping the Primer
    Don’t forget to prime plumbing pipes and fittings before gluing the pieces together. The primer strips away solvents and dirt and breaks down the glossy outer layer of plastic, softening it. When glue is applied, the two plastic surfaces are fused together, forming a watertight joint.
    Skipping the primer can introduce leaks further down the line, increasing the chances of pipe freeze.
  • Mistake 3: Not Back-Holding
    When tightening two hex fittings together, you need two wrenches, one on each fitting.
    Without two wrenches, you won’t be able to adequately tighten the connection. You’ll overtighten one side of it and under-tighten the other side. When tightening a hex fitting to a pipe, hold the pipe with a pipe wrench that’s appropriate and apply sufficient torque.
  • Mistake 4: Using a Dull Tubing Cutter
    The wheel on a tubing cutter will eventually get dull and when that happens, it will either leave a rough edge (which can lead to an improper joint, and a leak) or you’ll have to overtighten the cutter to make it cut, forcing the tubing out of round, and the result is the same: a leak.
  • Mistake 5: Heating the Solder, not the Copper
    It’s a common mistake when soldering together copper pipes. First-timers make the mistake of heating the solder, not the copper, reasoning that they’re going to just melt the solder into the joint.
    It doesn’t work that way. The torch will certainly melt the solder, but it won’t flow into the joint. The key is to heat the copper until it’s hot enough to melt the solder. When that happens, the solder will wick into the joint.

One of the most common tips for preparing your house for winter and keeping your pipes from freezing in the cold months is to maintain a proper indoor temperature throughout the house. You should also remember that you do not have to turn up the heat completely to prevent plumbing tubes from freezing.

Leave a Reply

Your email address will not be published. Required fields are marked *